Regular maintenance of Andis clippers extends blade life, improves cutting efficiency, and reduces the risk of skin irritation. This guide explains a practical, step-by-step approach to cleaning and sanitizing Andis clippers, using common tools and brand-specific products to keep your equipment in peak condition.
Quick Answer
For fast results, disconnect the clipper, remove blades, brush out hair with a dedicated clipper cleaning brush, apply clipper blade oil lubricant to moving parts, wipe with a disinfectant spray, and reassemble. Clean weekly if used daily, or after heavy use.
What You’ll Need
- Andis clipper cleaning brush kit
- Andis clipper blade oil lubricant
- Andis clipper blade disinfectant spray
- clipper cleaning and sanitizing kit for Andis clippers
- Andis clipper maintenance tool kit
Before You Start
Before beginning, unplug the clipper and remove the blade to access all moving parts. Work on a clean, well-lit surface and lay down a towel to catch clippings. Wear eye protection if splashes are possible. Keep the blades and internals dry unless you follow specific lubrication steps, as moisture can corrode components. Time estimates vary by model, but the basic routine takes about 10–20 minutes per session, with deeper maintenance taking longer.
Step-By-Step: How To Clean Andis Clippers
- Disconnect power and remove the blade from the clipper body, then place the blade on a towel or mat.
- Use the Andis clipper cleaning brush kit to gently remove hair and lint from the blade gaps, housing vents, and beneath the blade clamp.
- Wipe the clipper exterior with a soft cloth lightly dampened with water or a disinfectant spray, avoiding the switch and electrical ports.
- Apply a few drops of Andis clipper blade oil lubricant to the blade teeth and pivot points as recommended by the manufacturer, then run the clipper for a few seconds to distribute oil evenly.
- Spray a thin layer of Andis clipper blade disinfectant spray on the blade and clipper housing, following the product’s contact time guidelines to sanitize surfaces.
- Inspect the blade alignment and tension. If needed, use the Andis maintenance tool kit to adjust tension screws or tighten blade screws carefully without over-tightening.
- Reattach the blade, wipe away any excess oil or disinfectant, and run the clipper on a scrap material to confirm smooth operation and even cutting.
- Store the clipper in a dry, ventilated area. Periodically perform a full internal cleaning by repeating this routine and inspecting the power cord for wear.
- For heavy use or shared equipment, sanitize the entire unit after each client session using the disinfectant spray as the final step of cleaning.
- Schedule a deeper maintenance every 3–6 months, depending on usage, including blade sharpening or replacement as needed.
- Keep spare blades clean and oiled, and rotate them to extend life and maintain sharp cuts.
Troubleshooting
| Symptom | Likely Cause | Fix | Prevention |
|---|---|---|---|
| Clippers run rough or slow | Dirty blade or blockage | Clean thoroughly and re-oil | Regular brush-outs after each use |
| Blade not cutting evenly | Uneven blade tension | Adjust tension per manual | Use proper screw tightening procedure |
| Clippers overheat | Insufficient lubrication or dirty vents | Oil blade and clean vents | Frequent cleaning and proper oiling schedule |
| Disinfectant residue visible | Over-application | Wipe with clean cloth after dwell time | Follow contact times precisely |
Common Mistakes
- Ignoring blade alignment and tension during maintenance.
- Oiling too much or too little; inconsistent distribution.
- Using water on internal components or outlets that aren’t sealed.
- Skipping the disinfectant step when cleaning shared equipment.
- Delaying regular servicing, leading to blade wear and poor performance.
Pro tip: establish a routine that includes cleaning, oiling, and sanitizing at the end of each shift to maintain consistent results.
Tips For Best Results
- Always use the exact Andis blade oil lubricant designed for your model to prevent seizing or buildup.
- Keep a dedicated cloth and brush on hand to avoid cross-contamination between clients or tasks.
- Document maintenance dates to track blade longevity and anticipate replacements.
- Store blades in a dry, dust-free container to protect sharp edges between sessions.
- Consider a combined clipper cleaning and sanitizing kit for convenience and thorough coverage.
Call A Professional
Seek professional servicing if the clipper exhibits persistent overheating, unusual noises, electrical issues, or blade damage that you cannot safely address. Stop using the device until inspected. If there is visible blade corrosion or persistent cutting inconsistencies after routine cleaning, contact a trained technician.
FAQ
How often should I clean Andis clippers?
Clean after each use, with a deeper cleaning weekly for daily use and after heavy sessions.
Can I use water to clean the internal parts?
No. Avoid water on internal components; use approved cleaners and dry thoroughly.
Is it safe to oil I use on the blades?
Yes, use only Andis blade oil lubricant designed for your model.
What should I do if the blades rust?
Remove rust with a compatible blade cleaner and consider replacement if damage is severe.
How do I sanitize shared clippers?
Use a disinfectant spray on all high-contact surfaces after each client and allow proper dwell time before reuse.
Buying Guide
When selecting an Andis-friendly cleaning and maintenance setup, consider these factors to ensure compatibility and ease of use.
- <bSize and compatibility: Match products to your clipper model and blade sizes to ensure proper fit and operation.
- <bNoise level: Some maintenance tools and kits are quieter; consider this if the clippers are used in close client spaces.
- <bEnergy efficiency: Regular maintenance reduces motor strain, extending life and performance without extra energy use.
- <bControls and accessibility: Tools should be easy to apply with minimal disassembly, reducing setup time.
- <bPlacement: Store kits in a dry, ventilated area away from moisture and dust; keep cleaning supplies separate from disinfectants.
For professionals, combining an Andis clipper cleaning brush kit, blade oil lubricant, and a disinfectant spray in a single clipper maintenance tool kit can streamline workflows. When choosing, consider how often the kit will be used, whether it will serve multiple clippers, and if the included tools cover blade maintenance beyond basic cleaning. Do you need travel-size solutions for mobile work, or a full at-home setup for a shop? Evaluating these considerations helps tailor a maintenance plan that keeps clippers ready for precise, clean cuts.